Gennemkørselsafspærringen fra GPP Perimeter Protection kommer altid på tale, når det drejer sig om den højeste grad af sikkerhed. Det være sig wedge-barrier, bomme, Tyre Killer (dækødelægger) eller andre varianter: Vores gennemkørselsafspærringer beskytter indkørsler til følsomme områder mod uberettiget indtrængen og overskridelse af sikkerhedsperimeteren. Næste alle produkter er certificeret i henhold til PAS 68, IWA 14-1 eller ASTM til High Security-indsats. Fx stopper Wedge II med en penetration på 0 på stedet et køretøj, der nærmer sig.
Gennemkørselsafspærringer indenfor High Security-området skal aktivt beskytte områder og mennesker mod trusler, som fx angreb med køretøjer. I den forbindelse tilbyder vi forskellige gennemkørselsafspærringer, helt individuelle alt efter behov og omgivelser. Hvilket produkt der i sidste ende er det bedste til en bestemt virksomhed, organisation eller kommune, oplyser vi dig om i detaljer på en faglig og grundig måde – din indkørselsbeskyttelse bliver kun individuel med udgangspunkt i en behovsbaseret rådgivning og planlægning.
Certificeret kvalitet
GPP Perimeter Protection sætter den højest mulige grad af sikkerhed ifm. gennemkørselsafspærringer via internationale certificeringer. Den er kun, hvis man er forberedt på ekstreme trusselsscenarier, at man kan påstå at være virkelig forberedt på alt. Med gennemkørselsafspærringer fra GPP går du ikke på kompromis!
Yderst funktionelle og lidt vedligeholdelseskrævende
For at sikre funktionalitet samtidig med en lav grad af vedligeholdelse, styres vores gennemkørselsafspærringer af GPP’s egen WE-Tronic. Dette system har mange fordele mht. brugerkomforten. De har mange forskellige styringsmuligheder, der kan indstilles individuelt, uden at det påvirker sikkerhedsfunktionerne. Du finder mere Information om vores styreenhed på.
Din perimeterbeskyttelse – en lukket hele
Det gælder også indenfor sikkerhedsteknik, at helheden er mere end summen af de enkelte dele. Alligevel skal der selvfølgelig være forskellige komponenter: På den måde kan også Access-produkter som bomme og porte udvides med en gennemkørselsafspærring eller en Tyre Killer for at hæve sikkerhedsniveauet yderligere. I sidste ende er det ikke bare en kombination af enkelte elementer, men den samlede sikkerhed for dit område og alle personer, der opholder sig der.
Wedge II High Security
Wedge Barriers are our certified alternative to comprehensive bollard systems. They are ideal for use in areas without pedestrian traffic to ensure protection against unauthorised entry of vehicles. The Wedge II is the further improved successor model to our Wedge K12 . With an installation depth of only 300 mm, including 100 mm foundation lowering, this retractable system offers significant cost advantages through material savings and a shortened installation period. It also considerably simplifies dealing with any existing underground infrastructure.
This high security product is certified according to PAS 68, IWA 14-1 and ASTM F2656 standards – in each case with ZERO penetration.
Due to our control system WE Tronic II and sophisticated hydraulics, this shallow mounted road blocker is very user-friendly. With only one hydraulic cylinder and heavy-duty pressure spring pistons, a pressure accumulator with low storage volume can be used for EFO and RO3 functions. The drive cabinets used are also more space-saving as a result.
The system requires only one hydraulic connection and is also extremely low-maintenance due to its innovative oil filter. Further advantages of this product type are its low-noise scissor joints and its many options for customisation, e.g., with a safety skirt or a multi-coloured cover plate.
The already short actuation time of only 3.5 seconds can be further reduced to one second in an emergency with our optional Emergency Fast Operation (EFO) function.
Wedge II
Blocking height
1,000 mm
Blocking width
2,000 – 4,000 mm in 500 mm increments
Certification
PAS 68 V/7500[N3]/80/90:0.0/20.7 and
IWA 14-1 V/7200[N3C]/80/90:0.0 tested with 4 m blocking width
ASTM F2656-15 M50/P1 tested with 2 m blocking width
Operating time
Raising: approx. 3.5 sec., lowering: approx. 3.5 sec.
EFO (optional)
Approx. 1 sec.
Drive unit
Installed in separate drive cabinet
Installation depth
300 mm incl. 100 mm road covering
Options
Safety skirt, LED strip lighting, EFO + RO3, also see technical datasheet online
Tyre Killer Shark High Security
As with our standard Tyre Killer, the Tyre Killer SHARK also is available for blocking widths from 2 to 6 meters by coupling segments of 1.0- or 0.5-meters width each. The blocking height of 215 mm reliably stops hostile vehicles, with an actuation time of less than 1 second for both extension and retraction of the spikes. The shallow depth of just 490 mm allows the system to be used even where deeper foundations cannot be installed due to pipelines and conduits.
Tyre Killer Shark
Gate height
2,050 mm, 2,450 mm*
Clear width (CW)
3,000 – 6,000 mm in 500 mm increments
Infill
Bar infill RHS 30/20 mm
Foundation
Top edge of foundation 200 mm below finished floor level (Standard), other lowerings possible
Drive unit
One or two knee-joint drives (depending on model)
Control unit
Multifunctional, automatic control WE-Tronic II with integrated frequency converter
Interlocking
Via drive mechanism supported by interlocking of gate leaves through reception fork and in-feed roller
Certification
TÜV type-tested according to DIN EN 13241-1
Options
See technical datasheet online
RB1000CR Centurion Road Blocker High Security
The RB 1000 CR Centurion drive-through barrier ensures maximum security against unauthorized vehicles attempting to enter your perimeter. With a blocking height of 1000 mm and certified according to ASTM F2625, this extremely robust high-security barrier will provide flawless protection in any scenario. The product is simple to install, comes standard with user-friendly push-button control, and is suitable for duty cycling even at relatively high passage frequencies.
RB1000CR Centurion Road Blocker
Gate height
2,050 mm, 2,450 mm*
Clear width (CW)
3,000 – 6,000 mm in 500 mm increments
Infill
Bar infill RHS 30/20 mm
Foundation
Top edge of foundation 200 mm below finished floor level (Standard), other lowerings possible
Drive unit
One or two knee-joint drives (depending on model)
Control unit
Multifunctional, automatic control WE-Tronic II with integrated frequency converter
Interlocking
Via drive mechanism supported by interlocking of gate leaves through reception fork and in-feed roller
Certification
TÜV type-tested according to DIN EN 13241-1
Options
See technical datasheet online
RB980CR Sabre Surface Road Blocker High Security
The RB 980 CR Sabre Surface is the ideal solution for blocking passageways that need to be secured only temporarily or are not suitable for the installation of a sub-surface foundation. Made of heavy gauge steel and certified to PAS 68 standards, this drive-through barrier is extremely durable, even as it is low maintenance. If necessary, the barrier can be fully extended in less than one second via Emergency Fast Operation (EFO).
RB980CR Sabre Surface Road Blocker
Gate height
2,050 mm, 2,450 mm*
Clear width (CW)
3,000 – 6,000 mm in 500 mm increments
Infill
Bar infill RHS 30/20 mm
Foundation
Top edge of foundation 200 mm below finished floor level (Standard), other lowerings possible
Drive unit
One or two knee-joint drives (depending on model)
Control unit
Multifunctional, automatic control WE-Tronic II with integrated frequency converter
Interlocking
Via drive mechanism supported by interlocking of gate leaves through reception fork and in-feed roller
Certification
TÜV type-tested according to DIN EN 13241-1
Options
See technical datasheet online
Tyre Killer High Security
Our Tyre Killer system functions both as a visual deterrent and as a barrier with massive physical effect upon impact. The PPG Tyre Killer render any vehicle’s front axle inoperable and the Tyre Killer SHARK will destroy the tires. The system is available in heights of 450 mm or 215 mm respectively and in widths of between 2 to 6 metres. The actuation times are extremely short and, in case of the Tyre Killer SHARK, can be reduced to under one second.
Due to the low installation depth, our Tyre Killers are also suitable for installation in city centres and other areas with critical underground infrastructure such as subterranean conduits.
Tyre Killer
Gate height
2,050 mm, 2,450 mm*
Clear width (CW)
3,000 – 6,000 mm in 500 mm increments
Infill
Bar infill RHS 30/20 mm
Foundation
Top edge of foundation 200 mm below finished floor level (Standard), other lowerings possible
Drive unit
One or two knee-joint drives (depending on model)
Control unit
Multifunctional, automatic control WE-Tronic II with integrated frequency converter
Interlocking
Via drive mechanism supported by interlocking of gate leaves through reception fork and in-feed roller
